中文字幕一区二区久久人妻网站,天天日天天日天天射天天干,97人妻精品一二三区,精品久久久久中文字幕区爆

冷卻器是釀酒設備中遍及運用的一種冷卻設備，一起也適用于冶金、化工、礦山、輕工及重工等部門。首要用于設備潤滑油，變速系統油變器油，汽輪機油及磨火油的油系統中循環冷卻。

A cooler is a cooling device widely used in brewing equipment, which is also suitable for departments such as metallurgy, chemical industry, mining, light industry, and heavy industry. Primarily used for circulating cooling in equipment lubricating oil, variable speed system oil, transformer oil, turbine oil, and grinding oil systems.

不銹鋼冷卻器常見的特點有:任何換熱器都存有一個固定范圍內的輸出熱負荷。在選用時只能按用戶的大負荷選用，而在使用中由于諸多原因，負荷的變化量是很大的。據統計在低負荷時只能用到30左右(建筑規劃、工期、季節等因素)，這樣就造成了能源的浪費。而我廠的模塊組合式換熱器可按照您不同的階段和溫度變化來控制;傳熱系數高。

The common characteristics of stainless steel coolers are that any heat exchanger has a fixed range of output heat load. When selecting, it can only be based on the user's high load, and due to various reasons, the load changes greatly during use. According to statistics, only about 30 can be used at low loads (due to factors such as building planning, construction period, season, etc.), which leads to energy waste. Our modular combined heat exchanger can be controlled according to your different stages and temperature changes; High heat transfer coefficient.

由于冷卻器有效換熱管的使用，模塊化的結構，合理的過冷裝置，不易結垢。由于采用渦旋狀紫銅管，易形成湍流的流體對管壁有較強的沖刷作用，加之管型本身有熱補償能力，通過熱脹冷縮達到自潔，所以管內不易結垢;運行**可靠。負荷穩定。不會對負荷產生劇烈的回擊;結構緊湊，小巧。100萬大卡換熱量僅占地面350×350(mm);安裝快捷，維修方便。可不用專用機房，運到現場只需與系統管道接通即可。

Due to the effective energy-saving of the cooler and the use of heat exchange tubes, modular structure, and reasonable subcooling device, it is not easy to scale. Due to the use of vortex shaped copper pipes, turbulent fluids can easily form and have a strong flushing effect on the pipe wall. In addition, the pipe type itself has thermal compensation ability, which achieves self-cleaning through thermal expansion and contraction, making it less prone to scaling inside the pipe; Reliable operation. Stable load. Will not cause a severe rebound on the load; Compact and compact in structure. One million calories of heat exchange only occupy 350 × 350 (mm) on the ground; Quick installation and convenient maintenance. There is no need for a dedicated computer room, and when transported to the site, it only needs to be connected to the system pipeline.

(1)檢查各倒淋、放空閥是否靈活好用及開關位置，壓力表、溫度計是否全部裝好。

(1) Check if each drain and vent valve is flexible and easy to use, and if the switch position is correct. Also, check if all pressure gauges and thermometers are installed properly.

(2)檢查基礎、支座是否牢固，各部螺栓是否滿扣、緊固。

(2) Check whether the foundation and support are firm, and whether all bolts are fully fastened and tightened.

(3)投用時，先投冷流，后投熱流。

(3) When put into use, first apply cold flow and then apply heat flow.

(4)在投用冷介質或熱介質時，要保證副線暢通，再緩慢開出口閥，檢查無問題后開入口閥，一定要緩慢開，防止憋壓。投用過程要注意觀察設備變化情況。板式冷卻器投用后，隨著溫度壓力的變化，可能會出現泄漏現象，應及時進行檢查。

(4) When using cold or hot media, first ensure that the auxiliary line is unobstructed, then slowly open the inlet valve. After checking for no problems, open the inlet valve slowly to prevent pressure buildup. During the commissioning process, attention should be paid to observing changes in the equipment. After the plate cooler is put into use, leakage may occur with changes in temperature and pressure, and it should be checked in a timely manner.